English

Home › Family › 48V 52Ah Lithium Battery Pack (Ternary)

Ternary family — model page

48V 52Ah Lithium Battery Pack (Ternary)

The 48V point of the ternary family: a 48V 52Ah pack with a 54.6–39.0V working range, ≤40A continuous discharge with a ≤120A pulse, and a ≤1920W load rating, built for backup power, storage, mining, communications base stations and solar street lights.

Illustration of a green battery pack with a lightning bolt

Key data — 48V 52Ah Lithium Battery Pack (Ternary)

Nominal voltage / capacity48V / 52Ah
Working range54.6–39.0V
Charge current≤20A
Discharge≤40A continuous / ≤120A pulse
Maximum load≤1920W
Cycle life≥500 cycles
Internal resistance≤100mΩ
ConstructionFixed bracket + epoxy board + PVC
Dimensions / weight150×220×300mm / ≈13.5kg

48V 52Ah ratings in full

Charge current is ≤20A. Discharge is ≤40A continuous and ≤120A pulse, against a maximum load of ≤1920W. Cycle life is ≥500 cycles. The pack measures 150×220×300mm at about 13.5kg, built with a fixed bracket, epoxy board and PVC.

The 48V 52Ah specification

Nominal energy is about 2.5kWh (48V × 52Ah) in a 13.5kg pack — roughly 185Wh per kilogram for this pack. The working range, 54.6–39.0V, sets both ends of the pairing: chargers in the 54.6V class, and loads that must keep working down to 39.0V. The current pair divides the duty: ≤40A continuous for the sustained load, ≤120A pulse — three times the continuous figure — for starts and transients, with the ≤1920W load cap as the operative sustained ceiling. Charge at ≤20A returns a full charge in roughly two and a half to three hours. Internal resistance is ≤100mΩ. The construction — a fixed bracket, epoxy board and PVC — which tells the installer how the pack is meant to be mounted and finished: bracketed, not loose.

Where the 48V 52Ah pack fits

The model's applications: backup power, energy storage, mining, communications base stations and solar street lights. The pattern is stationary and infrastructure duty at the 48V bus — sites where the pack is installed once, cycled moderately, and read on a service visit. The cycle rating belongs in that reading: ≥500 cycles suits backup and infrastructure duty, and a buyer planning daily deep cycling at this voltage should compare the LiFePO4 systems (the 48V 40Ah AGV battery at 3000+ cycles, the forklift systems at 2000+ to 3000+) before choosing the ternary pack for its density. Inside its own family, the three forms divide by job: the module for builders assembling their own packs, the 18650 packs for devices, and this finished pack for the 48V installation.

Specifying a 48V 52Ah enquiry

State the continuous and peak draw against the ≤40A / ≤120A lines and the ≤1920W load cap, the charge source against the ≤20A limit and 54.6V ceiling, the mounting arrangement against the bracket construction and the 150×220×300mm envelope, and the cycling pattern against the ≥500 rating. Site duties (base stations, mining, street-light networks) should state the autonomy target and the service interval; the configuration answer follows from those figures rather than from the capacity alone.

Applications, walked one by one

The model's applications are unusually specific, and each entry sizes differently. Backup power: the duty is standby with rare deep discharges, where the ≥500-cycle rating is spent across years and the ≤40A continuous ceiling covers the backed-up load with headroom. Energy-storage systems: the pack as a 2.5kWh brick in a small bank, charged at ≤20A — a full charge in about two and a half hours at the ceiling. Mining equipment: the bracket-mounted, epoxy-board construction is the relevant line — a pack built to be fixed down and to take a machine's vibration environment, sized by the ≤1920W load cap. Communication base stations: the classic 48V-bus duty the pack's voltage class was born for, with long shallow cycling. Solar street lights: an overnight duty where the pack's whole capacity is the night's budget. One model, five duties, five different sizing conversations — the enquiry that names its duty gets the right one.

Construction: bracket, epoxy board and PVC

The construction — a fixed bracket, epoxy board and PVC — and it is worth reading closely. The bracket is the mounting answer: this pack is designed to be bolted into a machine or cabinet, not strapped; the envelope (150×220×300mm) and the mass (about 13.5kg) are the installer's two planning figures — the fixing points and the lift both work from them. The epoxy board is the cell-structure answer: a rigid, insulating carrier in place of shrink-wrap alone. The PVC finish is the handling answer: a wipe-clean, abrasion-tolerant skin for industrial environments. None of the three changes the electrical ratings. Buyers fitting the pack into a machine or cabinet are buying these three features; a vehicle-tray installation is a different mounting problem and should be raised in the enquiry.

Charging this pack: the 54.6V ceiling

The pack's working range tops at 54.6V and its charge current is ≤20A, which places its charger in the 54.6V class, where the line offers 54.6V models at 2A and 4A in aluminium and 2A in plastic, sized for packs of this class. At 4A the 52Ah pack refills overnight; at the 20A ceiling about two and a half hours — a charger at the ceiling is an enquiry specification, matched to the pack's limit rather than assumed from the class. The pairing discipline is the same across the range: the battery's ceiling governs, the charger's output is selected under it, and the two are never inferred from each other. A base-station or backup installation that will cycle the pack daily should state its turnaround window in the enquiry, because the window — not the capacity — is what sizes the charger.

Related pages