English

Home › Family › 12V 100Ah Polymer Battery Pack

Polymer family — model page

12V 100Ah Polymer Battery Pack

The large model of the polymer family: a 12V 100Ah pouch-format pack with a ≤20A continuous discharge, a ≤65A pulse and a 500-cycle rating, in a 95×155×190mm envelope. It is the family's answer where a shaped, light-format battery is needed at a capacity point the small instrument packs do not reach.

Illustration of a rounded purple battery pack with two terminals

Key data — 12V 100Ah Polymer Battery Pack

Nominal voltage / capacity12V / 100Ah
Maximum charge current≤15A
Continuous discharge≤20A
Pulse discharge≤65A
Cycle life500 cycles
Dimensions95×155×190mm

12V 100Ah ratings in full

Maximum charge current is ≤15A. Continuous discharge is ≤20A with a ≤65A pulse. Cycle life is 500 cycles. The pack measures 95×155×190mm, and its weight for a specific configuration is confirmed on enquiry.

The 12V 100Ah specification

Nominal energy is about 1.2kWh (12V × 100Ah) — the capacity of a small bank, in the polymer format. The current lines describe the duty it suits: ≤20A continuous is an instrument, lighting and standby profile sustained indefinitely, and the ≤65A pulse — better than three times the continuous figure — absorbs the start-up and transmission peaks such equipment draws. Charge at ≤15A maximum returns a full charge in roughly seven hours at the ceiling rate; gentler charge currents are a configuration choice under the ceiling, not a different model. The cycle rating is 500 cycles — this pack's own figure, and the 14.8V 10Ah polymer pack's own figure as well: this pack is specified for installations that cycle shallowly or occasionally, and buyers planning daily deep cycling should compare the LiFePO4 families, whose ratings run to thousands of cycles, before choosing the format for its shape.

Where the 12V 100Ah pack fits

Within the polymer family this is the capacity anchor: the 14.8V 10Ah model serves instruments and devices at about 148Wh, and this model serves the installations that need a kilowatt-hour-class store in a pouch-format envelope — monitoring and lighting installations, standby and backup units in shaped enclosures, and equipment whose housing was designed around a flat pack rather than a block battery. The 14.8V 10Ah model serves wireless monitoring, communications, medical devices, instruments, LED lighting, traffic signs, small appliances, power tools and toys. A 100Ah enquiry should state the application and its draw profile so the fit is confirmed against the ≤20A / ≤65A lines rather than assumed from the family name.

Specifying a 12V 100Ah polymer enquiry

State the continuous draw against the ≤20A line and the peak draw against the ≤65A pulse, the enclosure's internal dimensions against 95×155×190mm, the charge source against the ≤15A ceiling, and the cycling pattern against the 500-cycle rating. Weight is confirmed for the quoted configuration in the reply. Enquiries that arrive with the draw profile and the cavity dimensions get a configuration answer; enquiries that arrive with only a capacity get the questions above first, because at 100Ah the difference between a standby installation and a daily-cycling one is the difference between this pack and a different family.

What 1.2kWh does in a day

The pack stores 1.2kWh, and the honest way to read that is in loads. Lighting and electronics at 50W: a full day. A 200W appliance: six hours. At the ≤20A continuous ceiling itself — about 240W at 12V — the pack is spent in about five hours, and loads above that ceiling sit outside this model's continuous duty whatever the energy division suggests. Those divisions — nameplate energy against draw, with the continuous discharge rating checked against the same load — are the whole sizing method for a pack of this class. Where the duty is a vehicle auxiliary system, add the second check: the peak draw at motor start or compressor kick against the pulse side of the discharge specification at enquiry, because auxiliaries fail at their peaks, not at their averages.

The 500-cycle planning frame

Like its smaller sibling in this family, the pack is rated at 500 cycles, and the frame that makes that number useful is the duty pattern. The rating is a count, not a calendar: an auxiliary pack cycled every day spends the same 500 cycles far sooner than a backup pack cycled monthly, and a seasonal pack — the boat, the cabin, the harvest vehicle — sits between, its real enemy storage state rather than cycles: part-charged, cool and dry, checked on a calendar. The quotation conversation should therefore carry the expected cycling rate alongside the load figures, because the right spare-parts line and the right expectations follow from how fast the count will be spent. None of this is a defect in the pack; it is the shape of polymer construction at this capacity, priced and planned accordingly.

Fitting the pack: envelope before order

The pack's envelope is 95×155×190mm — a compact block for a 1.2kWh unit, shaped for equipment compartments and auxiliary bays rather than battery rooms. One figure the installer must ask for is the model's weight: it is confirmed at enquiry — an installation whose mounting is weight-critical should ask for it in the first message, with the compartment drawing. The electrical ratings, the cycle life and the dimensions complete the installer's inputs.

Request a quote

Send the model or your target specification — voltage, capacity, discharge current and envelope.

Related pages